GNS3でアクセスVLANの設定が不安定②
アクセスVLANの設定が不安定の件、
・ポートがリンクアップしてしばらくするとアクセスVLANの設定が消える。
・ポートを閉塞するとアクセスVLANの設定が復活する。
ということがわかった。
これは検証をする上でかなりまずい。。。
S32#sh int g1/1 summary
*: interface is up
IHQ: pkts in input hold queue IQD: pkts dropped from input queue
OHQ: pkts in output hold queue OQD: pkts dropped from output queue
RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)
TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)
TRTL: throttle count
Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL
-----------------------------------------------------------------------------------------------------------------
* GigabitEthernet1/1 0 2 0 0 1000 3 1000 2 0
S32#sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi0/0, Gi1/2, Gi1/3, Gi2/0
Gi2/1, Gi2/2, Gi2/3
30 VLAN0030 active Gi0/1, Gi1/0
100 VLAN100 active
200 VLAN0200 active
300 VLAN0300 active
1002 fddi-default act/unsup
1003 trcrf-default act/unsup
1004 fddinet-default act/unsup
1005 trbrf-default act/unsup
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0
100 enet 100100 1500 - - - - - 0 0
200 enet 100200 1500 - - - - - 0 0
300 enet 100300 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 trcrf 101003 4472 1005 3276 - - srb 0 0
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trbrf 101005 4472 - - 15 ibm - 0 0
VLAN AREHops STEHops Backup CRF
---- ------- ------- ----------
1003 7 7 off
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
S32#sh run int g1/1
Building configuration...
Current configuration : 98 bytes
!
interface GigabitEthernet1/1
switchport access vlan 30
media-type rj45
negotiation auto
end
S32#conf t
Enter configuration commands, one per line. End with CNTL/Z.
S32(config)#int g1/1
S32(config-if)#shutdown
S32(config-if)#
*Mar 10 14:16:18.374: %LINK-5-CHANGED: Interface GigabitEthernet1/1, changed state to administratively down
*Mar 10 14:16:19.374: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to down
S32(config-if)#end
S32#sh vla
*Mar 10 14:16:28.547: %SYS-5-CONFIG_I: Configured from console by console
S32#sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi0/0, Gi1/2, Gi1/3, Gi2/0
Gi2/1, Gi2/2, Gi2/3
30 VLAN0030 active Gi0/1, Gi1/0, Gi1/1
100 VLAN100 active
200 VLAN0200 active
300 VLAN0300 active
1002 fddi-default act/unsup
1003 trcrf-default act/unsup
1004 fddinet-default act/unsup
1005 trbrf-default act/unsup
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0
100 enet 100100 1500 - - - - - 0 0
200 enet 100200 1500 - - - - - 0 0
300 enet 100300 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 trcrf 101003 4472 1005 3276 - - srb 0 0
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trbrf 101005 4472 - - 15 ibm - 0 0
VLAN AREHops STEHops Backup CRF
---- ------- ------- ----------
1003 7 7 off
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
起動するために出てくる下記メッセージが関係してるのかも?
*Mar 10 15:32:21.865: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlan > 0 && vlan < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 850: pm_vlan_set_portlist)
-Traceback= 1C492C9z F385ABz FA5581z FA5245z F92213z 3013F8Fz F8E160z 3013F31z F8DE46z F8DDF9z 3013F8Fz F94B40z 3013F31z F9C955z F7C69Ez FF081Az
*Mar 10 15:32:21.866: %BIT-4-OUTOFRANGE: bit 0 is not in the expected range of 1 to 4095
-Traceback= 1C492C9z 196C71Fz 196BF98z FA5266z F92213z 3013F8Fz F8E160z 3013F31z F8DE46z F8DDF9z 3013F8Fz F94B40z 3013F31z F9C955z F7C69Ez FF081Az
*Mar 10 15:32:21.866: %BIT-4-OUTOFRANGE: bit 0 is not in the expected range of 1 to 4095
-Traceback= 1C492C9z 196C71Fz 196D35Cz FA527Az F92213z 3013F8Fz F8E160z 3013F31z F8DE46z F8DDF9z 3013F8Fz F94B40z 3013F31z F9C955z F7C69Ez FF081Az
*Mar 10 15:32:21.866: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlan > 0 && vlan < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 850: pm_vlan_set_portlist)
-Traceback= 1C492C9z F385ABz FA5581z FA5245z F92213z 3013F8Fz F8E160z 3013F31z F8DE46z F8DDF9z 3013F8Fz F94B40z 3013F31z F9C955z F7C69Ez FF081Az
*Mar 10 15:32:21.866: %BIT-4-OUTOFRANGE: bit 0 is not in the expected range of 1 to 4095
-Traceback= 1C492C9z 196C71Fz 196BF98z FA5266z F92213z 3013F8Fz F8E160z 3013F31z F8DE46z F8DDF9z 3013F8Fz F94B40z 3013F31z F9C955z F7C69Ez FF081Az
*Mar 10 15:32:21.866: %BIT-4-OUTOFRANGE: bit 0 is not in the expected range of 1 to 4095
-Traceback= 1C492C9z 196C71Fz 196D35Cz FA527Az F92213z 3013F8Fz F8E160z 3013F31z F8DE46z F8DDF9z 3013F8Fz F94B40z 3013F31z F9C955z F7C69Ez FF081Az
*Mar 10 15:32:21.866: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlan > 0 && vlan < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 850: pm_vlan_set_portlist)
-Traceback= 1C492C9z F385ABz FA5581z FA5245z F92213z 3013F8Fz F8E160z 3013F31z F8DE46z F8DDF9z 3013F8Fz F94B40z 3013F31z F9C955z F7C69Ez FF081Az
*Mar 10 15:32:21.867: %BIT-4-OUTOFRANGE: bit 0 is not in the expected range of 1 to 4095
-Traceback= 1C492C9z 196C71Fz 196BF98z FA5266z F92213z 3013F8Fz F8E160z 3013F31z F8DE46z F8DDF9z 3013F8Fz F94B40z 3013F31z F9C955z F7C69Ez FF081Az
*Mar 10 15:32:21.867: %BIT-4-OUTOFRANGE: bit 0 is not in the expected range of 1 to 4095
-Traceback= 1C492C9z 196C71Fz 196D35Cz FA527Az F92213z 3013F8Fz F8E160z 3013F31z F8DE46z F8DDF9z 3013F8Fz F94B40z 3013F31z F9C955z F7C69Ez FF081Az
*Mar 10 15:32:22.613: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlan > 0 && vlan < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 870: pm_vlan_test_portlist)
-Traceback= 1C492C9z F385ABz FA54E0z FA5617z F9398Bz F93AF1z 3013F8Fz F9C941z F7C69Ez FF15B7z F0AF14z F0E376z 3B0D01Cz 3B0CF6Dz F0DDABz F0C923z
*Mar 10 15:32:22.613: %PM-3-INTERNALERROR: Port Manager Internal Software Error (pm_vlan_test_portlist(vlan, pd->globalNumber): ../switch/pm/pm_vlan.c: 1777: pm_vlan_rem_port)
-Traceback= 1C492C9z F385ABz FA578Bz F9398Bz F93AF1z 3013F8Fz F9C941z F7C69Ez FF15B7z F0AF14z F0E376z 3B0D01Cz 3B0CF6Dz F0DDABz F0C923z F0BD6Bz
*Mar 10 15:32:22.613: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlan > 0 && vlan < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 860: pm_vlan_clear_portlist)
-Traceback= 1C492C9z F385ABz FA58F1z FA5665z F9398Bz F93AF1z 3013F8Fz F9C941z F7C69Ez FF15B7z F0AF14z F0E376z 3B0D01Cz 3B0CF6Dz F0DDABz F0C923z
*Mar 10 15:32:22.614: %BIT-4-OUTOFRANGE: bit 0 is not in the expected range of 1 to 4095
-Traceback= 1C492C9z 196C71Fz 196BF98z FA5699z F9398Bz F93AF1z 3013F8Fz F9C941z F7C69Ez FF15B7z F0AF14z F0E376z 3B0D01Cz 3B0CF6Dz F0DDABz F0C923z
*Mar 10 15:32:22.614: %PM-3-INTERNALERROR: Port Manager Internal Software Error (pm_vtpvlan_bitlist_test(&pd->operInfo.trunkVlans, vlan): ../switch/pm/pm_vlan.c: 1789: pm_vlan_rem_port)
-Traceback= 1C492C9z F385ABz FA5700z F9398Bz F93AF1z 3013F8Fz F9C941z F7C69Ez FF15B7z F0AF14z F0E376z 3B0D01Cz 3B0CF6Dz F0DDABz F0C923z F0BD6Bz
*Mar 10 15:32:22.614: %BIT-4-OUTOFRANGE: bit 0 is not in the expected range of 1 to 4095
-Traceback= 1C492C9z 196C71Fz 196C008z FA56A7z F9398Bz F93AF1z 3013F8Fz F9C941z F7C69Ez FF15B7z F0AF14z F0E376z 3B0D01Cz 3B0CF6Dz F0DDABz F0C923z
*Mar 10 15:32:24.282: %SPANTREE-7-RECV_1Q_NON_TRUNK: Received 802.1Q BPDU on non trunk GigabitEthernet0/3 VLAN1.
*Mar 10 15:32:24.282: %SPANTREE-7-BLOCK_PORT_TYPE: Blocking GigabitEthernet0/3 on VLAN0001. Inconsistent port type.
*Mar 10 15:34:44.854: %PLATFORM-5-SIGNATURE_VERIFIED: Image 'flash0:/vios_l2-adventerprisek9-m' passed code signing verification
